Generic OBD-II (SAE J2012) powertrain P-codes
Every code on this list links to a full page with the likely causes and the safe checks to try first.
| Code | What it means |
|---|---|
| P0010 | The computer detects a fault in the circuit that controls the bank 1 intake camshaft timing actuator (oil control solenoid). |
| P0011 | The computer sees the bank 1 intake camshaft sitting further ahead than commanded and cannot bring it back to target. |
| P0012 | The bank 1 intake camshaft is running further behind its target position than the computer allows. |
| P0013 | The computer detects a fault in the circuit that controls the bank 1 exhaust camshaft timing actuator (oil control solenoid). |
| P0014 | The bank 1 'B' camshaft (usually the exhaust cam) is ahead of its commanded position and the computer cannot correct it. |
| P0015 | The bank 1 exhaust camshaft is running further behind its target position than the computer allows. |
| P0016 | The computer sees the crankshaft and bank 1 'A' camshaft positions out of step with each other, meaning engine timing may be off. |
| P0017 | The engine computer finds that the crankshaft and the bank 1 exhaust camshaft are not turning in the expected step with each other, so valve timing looks wrong. |
| P0100 | The engine computer has found a fault in the mass air flow sensor or its circuit, so it cannot measure incoming air correctly. |
| P0101 | The mass airflow reading does not make sense compared with other engine data, so fuel metering may be off. |
| P0102 | The MAF sensor signal is lower than expected, so the computer thinks less air is entering the engine than really is. |
| P0103 | The mass air flow sensor is sending a signal that is higher than the engine computer expects, so the airflow reading is not trusted. |
| P0105 | The engine computer sees a fault in the manifold pressure (MAP) sensor or its circuit, so it cannot gauge engine load accurately. |
| P0106 | The intake manifold pressure (or barometric) sensor reports a value that does not match what the engine is doing. |
| P0107 | The MAP sensor signal is lower than the computer expects, so engine load is misread. |
| P0108 | The MAP sensor signal is higher than the computer expects, so engine load is misread. |
| P0110 | The intake air temperature sensor or its wiring is giving a signal outside the expected range. |
| P0111 | The intake air temperature reading does not match what the computer expects compared with other sensors. |
| P0112 | The intake air temperature sensor is reporting a very low voltage, which the computer reads as extremely hot intake air. |
| P0113 | The intake air temperature sensor is sending a signal that looks far too cold, which usually points to an open circuit or bad sensor. |
| P0115Safety | The engine coolant temperature sensor or its wiring is giving a signal outside the expected range. |
| P0116Safety | The engine coolant temperature reading does not make sense compared with other data, such as how the engine warms up. |
| P0117Safety | The coolant temperature sensor reports a reading that looks far too hot, which the computer may trust and run the engine in a protective mode. |
| P0118Safety | The engine coolant temperature sensor circuit is reading a very high voltage, which the computer interprets as extremely cold coolant. |
| P0119Safety | The coolant temperature sensor signal drops out or jumps around, so the computer cannot tell how hot the engine is. |
| P0120 | The computer sees a fault in the throttle position or accelerator pedal sensor A circuit. |
| P0121 | The throttle position (or accelerator pedal) sensor A signal is outside the range the computer expects. |
| P0122 | The throttle position sensor voltage is lower than it should be, so the computer cannot read throttle opening properly. |
| P0123 | The throttle position (or accelerator pedal position) sensor A is sending a voltage higher than expected, so the computer cannot read how far the throttle is… |
| P0125 | The engine is not warming up to its normal operating temperature quickly enough for the computer to start efficient fuel control. |
| P0128 | The engine is taking too long to warm up or never reaches its normal operating temperature. |
| P0130 | The computer sees a signal from the upstream oxygen sensor on bank 1 that does not fit normal operation. |
| P0131 | The upstream oxygen sensor on bank 1 is reporting a voltage that stays too low. |
| P0132 | The upstream oxygen sensor on bank 1 is reporting a voltage that stays too high. |
| P0133 | The upstream oxygen sensor reacts more slowly than expected, which reduces the computer's ability to control the fuel mixture. |
| P0134 | The upstream oxygen sensor signal is not changing at all, so the computer cannot adjust fuel properly. |
| P0135 | The heater inside the upstream oxygen sensor is not working as expected, so the sensor is slow to become active. |
| P0136 | The computer sees a signal from the oxygen sensor behind the catalytic converter on bank 1 that does not fit normal operation. |
| P0137 | The downstream (after-catalyst) oxygen sensor voltage is lower than expected. |
| P0138 | The oxygen sensor behind the catalytic converter on bank 1 is reporting a voltage that stays too high. |
| P0139 | The oxygen sensor behind the catalytic converter on bank 1 is reacting too slowly to changes in the exhaust. |
| P0140 | The computer is seeing no signal from the oxygen sensor behind the catalytic converter on bank 1. |
| P0141 | The heater in the downstream oxygen sensor is not operating as expected. |
| P0150 | The computer sees a signal from the upstream oxygen sensor on bank 2 that does not fit normal operation. |
| P0155 | The heater inside the upstream oxygen sensor on bank 2 is not working properly, so the sensor warms up too slowly. |
| P0161 | The heater inside the oxygen sensor behind the catalytic converter on bank 2 is not working properly. |
| P0170 | The computer cannot keep the air-fuel mixture on bank 1 in balance and has hit its correction limit. |
| P0171 | The computer is adding more fuel than normal on bank 1 because it sees too much air or too little fuel. |
| P0172Safety | The computer is removing fuel because bank 1 appears to be getting too much fuel for the air. |
| P0173 | The computer cannot keep the air-fuel mixture on bank 2 in balance and has hit its correction limit. |
| P0174 | The engine computer is adding extra fuel on bank 2 but still sees too much air for the fuel being supplied. |
| P0175Safety | The computer is cutting fuel on bank 2 because the mixture appears too rich. |
| P0176 | The computer sees a fault in the fuel composition (ethanol content) sensor circuit. |
| P0201 | The engine computer cannot get the expected response from the cylinder 1 fuel injector or its circuit. |
| P0202 | The engine computer cannot get the expected response from the cylinder 2 fuel injector or its circuit. |
| P0203 | The engine computer cannot get the expected response from the cylinder 3 fuel injector or its circuit. |
| P0204 | The engine computer cannot get the expected response from the cylinder 4 fuel injector or its circuit. |
| P0205 | The engine computer cannot get the expected response from the cylinder 5 fuel injector or its circuit. |
| P0206 | The engine computer cannot get the expected response from the cylinder 6 fuel injector or its circuit. |
| P0207 | The engine computer cannot get the expected response from the cylinder 7 fuel injector or its circuit. |
| P0208 | The engine computer cannot get the expected response from the cylinder 8 fuel injector or its circuit. |
| P0217Safety | The engine temperature has gone above the safe limit the computer allows. |
| P0218Safety | The automatic transmission fluid has become hotter than the computer allows. |
| P0220 | The computer sees a fault in the throttle position or accelerator pedal sensor B circuit, which it compares with sensor A. |
| P0230 | The engine computer detects a fault in the electrical circuit that switches the fuel pump on. |
| P0234 | The turbo or supercharger is making more boost than the computer asked for. |
| P0299 | The turbo or supercharger is not making as much boost as the computer asked for. |
| P0300Safety | The engine is misfiring on more than one cylinder or on cylinders that change. |
| P0301Safety | The computer has counted enough misfires on cylinder 1 to set a cylinder-specific code. |
| P0302Safety | The computer has counted enough misfires on cylinder 2 to set a cylinder-specific code. |
| P0303Safety | The computer has counted enough misfires on cylinder 3 to set a cylinder-specific code. |
| P0304Safety | The computer has counted enough misfires on cylinder 4 to set a cylinder-specific code. |
| P0305Safety | The computer has counted enough misfires on cylinder 5 to set a cylinder-specific code. |
| P0306Safety | The computer has counted enough misfires on cylinder 6 to set a cylinder-specific code. |
| P0307Safety | The computer has counted enough misfires on cylinder 7 to set a cylinder-specific code. |
| P0308Safety | The computer has counted enough misfires on cylinder 8 to set a cylinder-specific code. |
| P0325 | The bank 1 knock sensor signal is outside its expected range, so the engine may not detect or protect against knock. |
| P0326 | The knock sensor on bank 1 is giving a signal outside the expected range, so the computer cannot reliably detect engine knock. |
| P0335 | The engine computer is not getting a proper signal from the crankshaft position sensor, which it needs to time spark and fuel. |
| P0340 | The engine computer cannot read a proper signal from the camshaft position sensor, which it uses to time spark and fuel injection. |
| P0341 | The camshaft position sensor A signal on bank 1 is irregular or does not match what the computer expects. |
| P0344 | The camshaft position sensor A signal on bank 1 drops out on and off. |
| P0365 | The computer sees a fault in the bank 1 camshaft position sensor B (exhaust) circuit. |
| P0400 | The computer finds that the EGR system is not flowing the amount of exhaust gas expected. |
| P0401 | The computer expects more exhaust gas to be recirculated into the intake than it is measuring. |
| P0402 | The computer finds more exhaust gas flowing through the EGR system than expected. |
| P0403 | The computer sees a fault in the electrical circuit that controls the EGR valve or solenoid. |
| P0404 | The EGR system is not responding as expected to the computer's commands. |
| P0405 | The EGR valve position sensor is reporting a voltage lower than expected. |
| P0406 | The EGR valve position sensor is reporting a voltage higher than expected. |
| P0410 | The system that blows fresh air into the exhaust during cold starts to cut emissions has a fault. |
| P0411 | The secondary air injection system is not moving the amount of air the computer expects. |
| P0412 | The computer sees a fault in the circuit for the secondary air injection switching valve (solenoid) A. |
| P0417 | The computer finds an electrical short in the circuit for the secondary air injection switching valve (solenoid) B. |
| P0420Safety | The bank 1 catalytic converter is not cleaning exhaust as well as the computer expects. |
| P0430Safety | The bank 2 catalytic converter is not cleaning exhaust well enough. |
| P0440Safety | The fuel vapor recovery system failed its self-test without a more specific cause. |
| P0441Safety | The vapor purge flow to the engine is outside what the computer expects. |
| P0442Safety | The fuel vapor system has a very small leak. |
| P0443Safety | The computer detects an electrical fault in the purge valve or its circuit. |
| P0444 | The computer sees an open circuit in the control wiring of the EVAP purge valve, which feeds fuel vapor into the engine. |
| P0446Safety | The EVAP vent valve or its circuit is not working as expected. |
| P0447 | The computer sees an open circuit in the EVAP vent valve control wiring. |
| P0448 | The computer sees a short in the EVAP vent valve control wiring. |
| P0449 | The computer detects a fault in the EVAP vent valve or its solenoid circuit. |
| P0450 | The computer sees a faulty signal from the EVAP pressure sensor that measures fuel tank vapor pressure. |
| P0451 | The EVAP pressure sensor reading does not match what the computer expects. |
| P0452 | The EVAP pressure sensor is reporting a voltage lower than expected. |
| P0453 | The EVAP pressure sensor is reporting a voltage higher than expected. |
| P0455Safety | The fuel vapor system has a large leak, most often an open or loose gas cap. |
| P0456Safety | The fuel vapor system has an extremely small leak. |
| P0457 | The computer has found a leak in the fuel vapor system, often a loose or missing fuel cap. |
| P0460 | The computer sees an unreasonable signal from the fuel level sensor (part of the fuel pump assembly), so the fuel reading may be wrong. |
| P0463 | The fuel level sensor is sending a signal that is higher than the tank could hold, so the fuel reading is unreliable. |
| P0480Safety | The computer cannot properly control the electric engine cooling fan 1, so the engine may not stay cool at idle or in traffic. |
| P0481Safety | The computer cannot properly control the electric engine cooling fan 2, so the engine may not stay cool at idle or in traffic. |
| P0496Safety | The computer sees vapor flow when purge should be closed. |
| P0500 | The engine computer is not getting a believable vehicle speed signal from the speed sensor. |
| P0504Safety | The two brake switch signals do not agree, so the computer cannot be sure whether the brake pedal is pressed. |
| P0505 | The computer cannot hold engine idle at its target speed. |
| P0506 | The engine idle speed is lower than the computer is trying to hold. |
| P0507 | The engine idles faster than the computer's target. |
| P0510 | The computer sees a fault in the switch or sensor that tells it when the throttle is fully closed. |
| P0521 | The oil pressure sensor reading does not make sense for how the engine is running, or oil pressure may truly be low. |
| P0522 | The oil pressure sensor circuit is reporting low voltage, which can mean real low oil pressure or a sensor or wiring fault. |
| P0523 | The oil pressure sensor circuit is reporting high voltage, which can mean a sensor or wiring fault or a real oil pressure problem. |
| P0560 | The computer sees the vehicle's system voltage outside the normal range while the engine runs. |
| P0562 | System voltage has dropped below the level the computer expects. |
| P0563 | The computer sees the vehicle's system voltage higher than it should be. |
| P0600Safety | The engine computer has lost or garbled communication with another control module. |
| P0601 | The engine computer failed its own memory self-check, so its stored program may be damaged. |
| P0602 | The engine computer has found that its programming or memory is not what it should be. |
| P0603 | The engine computer's keep-alive memory, which stores learned settings, has failed, so it falls back to default settings. |
| P0604 | The engine computer has found a fault in its own working memory. |
| P0606 | The engine computer's self-check has found a problem with its internal processor. |
| P0620 | The engine computer sees a fault in the circuit that controls the alternator. |
| P0625 | The alternator field circuit voltage is lower than the engine computer expects, so the alternator may not charge properly. |
| P0630 | The vehicle identification number stored in the engine computer is missing or does not match. |
| P0634Safety | The engine or transmission control module reports that its own internal temperature is above the safe limit. |
| P0650 | The engine computer cannot properly control the check engine light circuit. |
| P0685 | The engine computer sees a problem with the relay that supplies it with power. |
| P0700 | The transmission control module has logged its own fault and has asked the engine computer to turn on the check engine light. |
| P0705 | The computer gets an erratic or invalid signal from the sensor that tells it which gear (park, reverse, neutral, drive) is selected. |
| P0706 | The transmission range sensor (gear position switch) is giving a signal that does not make sense for the selected gear. |
| P0710 | The computer sees a fault in the transmission fluid temperature sensor circuit. |
| P0711 | The transmission fluid temperature sensor reading does not make sense for how the vehicle is operating. |
| P0713 | The transmission fluid temperature sensor is reporting an unusually high reading. |
| P0715 | The transmission input speed sensor signal is faulty. |
| P0716 | The transmission input (turbine) speed sensor gives an unstable or unreasonable signal. |
| P0717 | The transmission computer is getting no signal from the input (turbine) speed sensor. |
| P0720 | The transmission computer is getting a poor or erratic signal from the output speed sensor, which tracks how fast the transmission output shaft is turning. |
| P0730 | The transmission computer finds that the actual gear ratio does not match the gear it commanded. |
| P0731 | The transmission computer finds that the speed ratio in first gear is not what it should be, which usually means slipping or a failure to engage first gear. |
| P0732 | The transmission computer finds that the speed ratio in second gear is not what it should be, which usually means slipping or a failure to engage second gear. |
| P0733 | The transmission computer finds that the speed ratio in third gear is not what it should be, which usually means slipping or a failure to engage third gear. |
| P0734 | The transmission computer finds that the speed ratio in fourth gear is not what it should be, which usually means slipping or a failure to engage fourth gear. |
| P0735 | The transmission computer finds that the speed ratio in fifth gear is not what it should be, which usually means slipping or a failure to engage fifth gear. |
| P0740 | The computer sees a fault in the circuit or operation of the torque converter clutch (lockup) system. |
| P0741 | The torque converter clutch is not locking up when the computer commands it, so the engine and transmission slip. |
| P0743 | The computer sees an electrical fault in the torque converter clutch solenoid circuit. |
| P0746 | The transmission pressure control solenoid A is not regulating hydraulic pressure as the computer asks. |
| P0750 | The computer sees a problem with shift solenoid A or its circuit, which controls hydraulic pressure for gear changes. |
| P0755 | The computer sees a problem with shift solenoid B or its circuit, which controls hydraulic pressure for gear changes. |
| P0760 | The computer sees a problem with shift solenoid C or its circuit, which controls hydraulic pressure for gear changes. |
| P0765 | The computer sees a problem with shift solenoid D or its circuit, which controls hydraulic pressure for gear changes. |
| P0770 | The computer sees a problem with shift solenoid E or its circuit, which controls hydraulic pressure for gear changes. |
| P0775 | The computer sees a problem with pressure control solenoid B or its circuit, which sets hydraulic pressure inside the transmission. |
| P0780 | The transmission is not shifting the way the computer commands. |
| P0781 | The transmission is not completing the first-to-second gear shift correctly; the actual gear ratio does not match what the computer asked for. |
| P0782 | The transmission is not completing the second-to-third gear shift correctly; the actual gear ratio does not match what the computer asked for. |
| P0783 | The transmission is not completing the third-to-fourth gear shift correctly; the actual gear ratio does not match what the computer asked for. |
| P0784 | The transmission is not completing the fourth-to-fifth gear shift correctly; the actual gear ratio does not match what the computer asked for. |
| P0850 | The computer is getting an abnormal signal from the park/neutral position switch, which tells it whether the transmission is in park or neutral. |
| P2002Safety | The diesel particulate filter is not trapping or clearing soot as well as the computer expects. |
| P2006 | The flaps inside the intake manifold that change airflow are stuck closed on bank 1, so the engine breathes poorly at higher rpm. |
| P2008 | The computer finds an open circuit in the control for the intake manifold runner flaps on bank 1. |
| P2015 | The computer finds that the intake runner flaps are not where the position sensor says they should be. |
| P2070 | The valve that adjusts intake airflow for low-rpm power is stuck open. |
| P2096 | The oxygen sensor behind the catalytic converter on bank 1 is seeing too much oxygen, and the computer cannot correct it. |
| P2097 | The oxygen sensor behind the catalytic converter on bank 1 reports a rich mixture that the computer cannot correct. |
| P2098 | The oxygen sensor behind the catalytic converter on bank 2 is seeing too much oxygen, and the computer cannot correct it. |
| P2099 | The oxygen sensor behind the catalytic converter on bank 2 reports a rich mixture that the computer cannot correct. |
| P2101 | The throttle plate is not moving to the position the computer commanded. |
| P2106 | The computer found a serious fault in the electronic throttle system and has cut engine power to limp mode. |
| P2110 | The computer has found an electronic throttle fault and is limiting engine speed (rpm) and power. |
| P2111 | The throttle plate is stuck more open than the computer commanded. |
| P2112 | The throttle plate is stuck closed, so the engine cannot get the air it needs. |
| P2119 | The throttle plate position does not match the position the computer commanded. |
| P2122 | The computer sees a very low signal from accelerator pedal position sensor D, so it cannot tell how far the pedal is pressed. |
| P2127 | The computer sees a very low signal from accelerator pedal position sensor E, so it cannot tell how far the pedal is pressed. |
| P2135 | The two throttle position signals disagree with each other, so the computer cannot trust the throttle reading. |
| P2138 | The two accelerator pedal sensor signals disagree with each other, so the computer cannot trust the pedal reading. |
| P2187 | At idle the engine computer is adding fuel on bank 1 but still sees too much air for the fuel being delivered. |
| P2188 | At idle the engine computer is cutting fuel on bank 1 but still sees too much fuel for the air entering. |
| P2189 | At idle the engine computer is adding fuel on bank 2 but still sees too much air for the fuel being delivered. |
| P2190 | At idle the engine computer is cutting fuel on bank 2 but still sees too much fuel for the air entering. |
| P2197 | The bank 2 upstream oxygen sensor reads lean and stays there, suggesting a real lean condition or a sensor fault. |
| P2270 | The oxygen sensor behind the catalytic converter on bank 1 keeps reporting a lean exhaust and is not switching normally. |
| P2271 | The oxygen sensor behind the catalytic converter on bank 1 keeps reporting a rich exhaust and is not switching normally. |
| P2272 | The oxygen sensor behind the catalytic converter on bank 2 keeps reporting a lean exhaust and is not switching normally. |
| P2300Safety | The computer sees too little voltage in the control circuit for ignition coil A, so that cylinder may not fire. |
| P2303Safety | The computer sees too little voltage in the control circuit for ignition coil B, so that cylinder may not fire. |
| P2304Safety | The computer sees too much voltage in the control circuit for ignition coil B, so that cylinder may not fire. |
| P2305Safety | The computer finds a fault in the high-voltage side of ignition coil B, so the spark plug may not fire. |
| P2310Safety | The computer sees too much voltage in the control circuit for ignition coil D, so that cylinder may not fire. |
Fault Code Fix is independent and is not affiliated with any manufacturer. Brand names identify the products the codes apply to.
Find a code
Washers
Bosch washer E/F codes Electrolux/Frigidaire front-load washer E-codes Electrolux front-load washer display messages Frigidaire front-load washer F2 GE GFW front-load washer numeric fault codes GE Profile UltraFast combo washer/dryer codes LG front-load washer display codes Samsung washer codes (front and top load) (front-load washers) Whirlpool-family F#E# and display codes (Whirlpool, Maytag, Amana, KitchenAid) (front-load washers) Frigidaire top-load washer E-codes GE top-load washer display messages LG top-load washer display codes Samsung washer codes (front and top load) (top-load washers) Whirlpool-family F#E# and display codes (Whirlpool, Maytag, Amana, KitchenAid) (top-load washers) LG WashTower washer-side display codesDryers
Bosch dryer E-codes Electrolux dryer E-codes (IQ-Touch platform) Frigidaire Affinity dryer E-codes GE GFD-series dryer numeric fault codes LG dryer display codes Samsung dryer codes (electric, gas, heat pump) Whirlpool/Kenmore older F0# dryer codes Whirlpool-family dryer F#E# and display codesDishwashers
Bosch dishwasher E-codes Frigidaire/Electrolux dishwasher codes GE dishwasher C-codes and status messages LG dishwasher display codes Samsung dishwasher letter/number codes Whirlpool-family dishwasher F#E# codes (display models, current manufacturer list) Whirlpool-family HE dishwasher F#E# and flash-count codes (older electronic-control models)Ranges & Microwaves
GE microwave error codes LG microwave codes Samsung microwave codes Whirlpool-family over-the-range microwave F codes Bosch oven / microwave codes Bosch freestanding range codes Frigidaire / Electrolux electric range F codes GE / GE Profile / Café range and wall oven F codes LG range codes Samsung range / oven codes Whirlpool-family range F# / F#E# codes Whirlpool-family wall oven / range F9 miswire codeRefrigerators
Frigidaire refrigerator alarms GE refrigerator codes LG refrigerator Er codes Refrigerator symptom guides (all brands) Samsung refrigerator error codes Whirlpool refrigerator indicatorsWater Heaters
A. O. Smith / State FVIR gas control flash codes Bradford White Honeywell V1 gas control LED codes Bradford White Honeywell V2 / White-Rodgers electronic gas control LED codes Bradford White UPV75 power-vent LED codes GE GeoSpring hybrid heat pump fault codes GE Profile GeoSpring hybrid fault codes (2025+ models) Rheem electric with e-control red blink codes Rheem hybrid heat pump water heater alarm codes Rheem PowerVent ESII LED flash codes Rheem super high efficiency gas alarm codes Rheem Super Sentinel electric fault codes Rheem/Ruud ultra low NOx 75 and 98 gallon gas error numbers Whirlpool Energy Smart electric diagnostic light Whirlpool gas water heater status-light flash codes Bosch gas tankless two-character codes Navien tankless E-codes Noritz tankless numeric error codes Rheem/Ruud IKONIC tankless (A-codes) Rheem/Ruud gas tankless (SVC820) codes Rinnai tankless diagnostic codes Takagi tankless numeric codesHeating & Cooling
Carrier 58-series two-digit status codes Goodman/Amana furnace integrated control LED flash codes Lennox EL180-series furnace E-codes Lennox iComfort furnace and air handler alert codes Lennox SureLight LED patterns Rheem/Ruud furnace status LED blinks Trane residential furnace LED flash codes York furnace integrated control LED codes Daikin mini-split codes Fujitsu RGLX lamp-blink codes Gree mini-split codes Lennox mini-split indoor unit codes Lennox mini-split outdoor unit codes LG split-system CH codes Mitsubishi Electric mini-split codes Pioneer Diamante-series codes Pioneer Quantum-series codes ecobee thermostat alerts and reminders Google Nest thermostat E help codes Google Nest thermostat W (Wi-Fi) codes Honeywell Home T6 Pro / FocusPRO alert codes Lennox iComfort S30 thermostat and system alert codesNo codes match your search.