Electrolux/Frigidaire front-load washer E-codes
Every code on this list links to a full page with the likely causes and the safe checks to try first. Covers Frigidaire, Electrolux.
| Code | What it means |
|---|---|
| E5A | The motor control board reports overheating (heat sink too hot). |
| E5B | The motor control board reports overheating (heat sink too hot). |
| E5C | The motor control board reports overheating (heat sink too hot). |
| E5D | The main control board and the motor control board are not communicating. |
| E5E | The main control board and the motor control board are not communicating. |
| E5F | The main control board and the motor control board are not communicating. |
| E11 | The washer took too long to fill with water during the wash phase. |
| E13 | Water is leaking from the tub, or air is escaping from the water-level sensor tube, so the water level will not hold. |
| E14 | The detergent dispenser drawer is not detected as closed. |
| E21 | Water is not pumping out of the tub fast enough, or takes too long to drain. |
| E23 | The control board reports a fault in the drain pump output (drain pump relay or drive). |
| E24 | The control board reports a fault in the drain pump output (sensing side), similar to E23. |
| E31 | The water-level pressure sensor is not communicating properly with the main control. |
| E32 | The water-level pressure sensor is giving an unstable or out-of-range reading. |
| E35 | The pressure sensor thinks the tub is overfilling with water. |
| E38 | The air trap or pressure-sensor air path appears clogged. |
| E41 | The control thinks the door is open or not latched. |
| E42 | The control does not recognize the door lock as engaged, which is a door lock device problem. |
| E44 | A control board fault is reported. |
| E45 | A control board fault is reported. |
| E46 | A control board fault is reported. |
| E47 | The control detects the door lock circuit open while the washer is spinning. |
| E48 | The control detects a problem in the door lock circuit (circuit unexpectedly closed). |
| E52 | The control is getting a bad speed signal from the drive motor's tachometer. |
| E55 | The drive motor is overheating or running below its expected speed. |
| E56 | The drive motor is drawing too much current. |
| E57 | The inverter or motor drive is drawing too much current. |
| E58 | A motor phase is drawing too much current. |
| E59 | The control sees no motor speed signal for about three seconds. |
| E62 | The wash water temperature reads too high. |
| E66 | The heating element relay or heater circuit failed. |
| E67 | The supply voltage to the control board's microprocessor is wrong. |
| E68Safety | The washer detected current leaking to ground on the heater, or the heater fuse opened. |
| E71 | The temperature sensor for the tub or heater is reading out of range. |
| E74 | The wash water is not heating up as expected. |
| E75 | The water temperature sensor circuit has failed. |
| E76 | The cold water temperature sensor reads outside its limits. |
| E84 | The recirculation pump output is faulty. |
| E91 | The control reports a user-interface fault (for example selector lights not working). |
| E95 | A communication error between control boards. |
| EB1 | The incoming power frequency is outside the allowed range. |
| EB2Safety | The incoming line voltage is too high (above about 130 volts). |
| EB3Safety | The incoming line voltage is too low (below about 90 volts). |
| EF1 | The drain pump appears clogged. |
| EF2 | The washer detected too many suds, caused by too much or the wrong detergent. |
Fault Code Fix is independent and is not affiliated with any manufacturer. Brand names identify the products the codes apply to.
Find a code
Washers
Bosch washer E/F codes Electrolux/Frigidaire front-load washer E-codes Electrolux front-load washer display messages Frigidaire front-load washer F2 GE GFW front-load washer numeric fault codes GE Profile UltraFast combo washer/dryer codes LG front-load washer display codes Samsung washer codes (front and top load) (front-load washers) Whirlpool-family F#E# and display codes (Whirlpool, Maytag, Amana, KitchenAid) (front-load washers) Frigidaire top-load washer E-codes GE top-load washer display messages LG top-load washer display codes Samsung washer codes (front and top load) (top-load washers) Whirlpool-family F#E# and display codes (Whirlpool, Maytag, Amana, KitchenAid) (top-load washers) LG WashTower washer-side display codesDryers
Bosch dryer E-codes Electrolux dryer E-codes (IQ-Touch platform) Frigidaire Affinity dryer E-codes GE GFD-series dryer numeric fault codes LG dryer display codes Samsung dryer codes (electric, gas, heat pump) Whirlpool/Kenmore older F0# dryer codes Whirlpool-family dryer F#E# and display codesDishwashers
Bosch dishwasher E-codes Frigidaire/Electrolux dishwasher codes GE dishwasher C-codes and status messages LG dishwasher display codes Samsung dishwasher letter/number codes Whirlpool-family dishwasher F#E# codes (display models, current manufacturer list) Whirlpool-family HE dishwasher F#E# and flash-count codes (older electronic-control models)Ranges & Microwaves
GE microwave error codes LG microwave codes Samsung microwave codes Whirlpool-family over-the-range microwave F codes Bosch oven / microwave codes Bosch freestanding range codes Frigidaire / Electrolux electric range F codes GE / GE Profile / Café range and wall oven F codes LG range codes Samsung range / oven codes Whirlpool-family range F# / F#E# codes Whirlpool-family wall oven / range F9 miswire codeRefrigerators
Frigidaire refrigerator alarms GE refrigerator codes LG refrigerator Er codes Refrigerator symptom guides (all brands) Samsung refrigerator error codes Whirlpool refrigerator indicatorsWater Heaters
A. O. Smith / State FVIR gas control flash codes Bradford White Honeywell V1 gas control LED codes Bradford White Honeywell V2 / White-Rodgers electronic gas control LED codes Bradford White UPV75 power-vent LED codes GE GeoSpring hybrid heat pump fault codes GE Profile GeoSpring hybrid fault codes (2025+ models) Rheem electric with e-control red blink codes Rheem hybrid heat pump water heater alarm codes Rheem PowerVent ESII LED flash codes Rheem super high efficiency gas alarm codes Rheem Super Sentinel electric fault codes Rheem/Ruud ultra low NOx 75 and 98 gallon gas error numbers Whirlpool Energy Smart electric diagnostic light Whirlpool gas water heater status-light flash codes Bosch gas tankless two-character codes Navien tankless E-codes Noritz tankless numeric error codes Rheem/Ruud IKONIC tankless (A-codes) Rheem/Ruud gas tankless (SVC820) codes Rinnai tankless diagnostic codes Takagi tankless numeric codesHeating & Cooling
Carrier 58-series two-digit status codes Goodman/Amana furnace integrated control LED flash codes Lennox EL180-series furnace E-codes Lennox iComfort furnace and air handler alert codes Lennox SureLight LED patterns Rheem/Ruud furnace status LED blinks Trane residential furnace LED flash codes York furnace integrated control LED codes Daikin mini-split codes Fujitsu RGLX lamp-blink codes Gree mini-split codes Lennox mini-split indoor unit codes Lennox mini-split outdoor unit codes LG split-system CH codes Mitsubishi Electric mini-split codes Pioneer Diamante-series codes Pioneer Quantum-series codes ecobee thermostat alerts and reminders Google Nest thermostat E help codes Google Nest thermostat W (Wi-Fi) codes Honeywell Home T6 Pro / FocusPRO alert codes Lennox iComfort S30 thermostat and system alert codesNo codes match your search.